Control Icon Guide

Next Generation Control Mill Operator's Manual

The Online Interactive Operator's Manual is currently available in English only.

A PDF version of the Operator's Manual is available for download in multiple languages. Click the link below to view the Operator's Manual in your language. Click "Continue" to view the online version in English.

Get a translated PDF Download Continue

The control screen shows icons to quickly give you information about machine status. Icons tell you about current machine modes, your program as it runs, and machine maintenance status.

The icon bar is near the bottom of the control pendant display, above the input and status bars.

Icon Bar Location

Name Icon Meaning
Setup Setup mode is locked; the control is in Run mode. Most machine functions are disabled or limited while the machine doors are open.
Setup Setup mode is unlocked; the control is in Setup mode. Most machine functions are available, but may be limited while the machine doors are open.
Door Open Warning, door is open.
Running The machine is running a program.
Jog An axis is jogging at the current jog rate.
Power Saving The power-saving servos-off feature is active. Setting 216, SERVO AND HYDRAULIC SHUTOFF, designates the time period allowed before this feature activates. Press a key to activate the servos.
Jog This icon appears while the control returns to the workpiece during a run-stop-jog-continue operation.
Jog You have pressed FEED HOLD during the return portion of a run-stop-jog-continue operation.
Jog This icon prompts you to jog away during a run-stop-jog-continue operation.
Feed Hold The machine is in feed hold. Axis motion has stopped, but the spindle continues to turn.
Feed The machine is executing a cutting move.
Rapid The machine is executing a non-cutting axis move (G00) at the fastest possible rate. Overrides can affect the actual rate.
Dwell The machine is executing a dwell (G04) command.
Restart The control scans the program before a restart if Setting 36 is ON.
Singbk Stop SINGLE BLOCK mode is active, and the control needs a command to continue.
Door Hold Machine motion has stopped because of door rules.
Jog Lock Jog lock is active. If you press an axis key, that axis moves at the current jog rate until you press JOG LOCK again, or the axis reaches its limit.
Remote Jog The optional remote jog handle is active.
Vector Jog For five-axis machines, the tool will jog along the vector defined by the rotary positions.
Gear Box Lube The spindle gear box oil level is low.
Rotary Lube Check and fill the rotary table lubrication oil reservoir.
TSC Filter Off Clean the Through-Spindle Coolant filter.
Low Coolant Fill the concentrate reservoir for the coolant refill system.
Low Lube The spindle lubrication oil system detected a low oil condition, or the axis ball screw lubrication system detected a low grease or low pressure condition.
Low Oil The rotary brake oil level is low.
Mist Filter Clean the mist extractor filter.
Coolant Warning Coolant level is low.
Low Air Flow Inch Mode - Air flow is not sufficient for correct machine operation.
Low Air Flow Metric Mode - Air flow is not sufficient for correct machine operation.
Maintenance A maintenance procedure is due.
Spindle When you press HANDLE SPINDLE, the jog handle varies the spindle override percentage.
Spindle When you press HANDLE FEED, the jog handle varies the feed rate override percentage.
Text Scroll When you press HANDLE SCROLL, the jog handle varies the spindle override percentage.
Mirroring Mirroring mode is active. Either G101 is programmed or Setting 45, 46, 47, 48, 80, or 250 (mirror image of axis X, Y, Z, A, B, or C) is set to ON.
Brake A rotary axis brake, or a combination of rotary axis brakes, is unclamped.
Brake A rotary axis brake, or a combination of rotary axis brakes, is clamped.
Low Voltage The PFDM detects low incoming voltage. If the condition continues, the machine cannot continue operation.
Low Voltage The Power Fault Detect Module (PDFM) detects incoming voltage that is too low to operate. The machine will not operate until the condition is corrected.
High Voltage The PFDM detects incoming voltage above a set limit, but still within operating parameters. Correct the condition to prevent damage to machine components.
High Voltage The PFDM detects incoming voltage that is too high to operate and could cause damage to the machine. The machine will not operate until the condition is corrected.
High Air The air pressure to the machine is too high to reliably operate pneumatic systems. Correct this condition to prevent damage to or incorrect operation of pneumatic systems. You may need to install a regulator at the machine’s air input.
Low Air The air pressure to the machine is too low to operate pneumatic systems. The machine will not operate until the condition is corrected. You may need a higher-capacity air compressor.
Low Air The air pressure to the machine is too low to reliably operate pneumatic systems. Correct this condition to prevent damage to or incorrect operation of pneumatic systems.
High Air The air pressure to the machine is too high to operate pneumatic systems. The machine will not operate until the condition is corrected. You may need to install a regulator at the machine’s air input.
E-Stop EMERGENCY STOP on the pendant has been pressed. This icon disappears when EMERGENCY STOP is released.
E-Stop EMERGENCY STOP on the pallet changer has been pressed. This icon disappears when EMERGENCY STOP is released.
E-Stop EMERGENCY STOP on the tool changer cage has been pressed. This icon disappears when EMERGENCY STOP is released.
E-Stop EMERGENCY STOP on an auxiliary device has been pressed. This icon disappears when EMERGENCY STOP is released.
Single Blk SINGLE BLOCK mode is active. The control executes programs (1) block at a time. Press CYCLE START to execute the next block.
Tool Life The tool life remaining is below Setting 240, or the current tool is the last one in its tool group.
Tool Life The tool or tool group has expired, and no replacement tools are available.
Opt Stop OPTIONAL STOP is active. The control stops the program at each M01 command.
Blk Delete BLOCK DELETE is active. The control skips program blocks that begin with a slash (/).
TC Door Open The side-mount tool changer door is open.
TL CCW The side-mount tool changer carousel is rotating counter-clockwise.
TL CW The side-mount tool changer carousel is rotating clockwise.
Tool Change A tool change is in progress.
Unclamped The tool in the spindle is unclamped.
Probe The probe system is active.
Conveyor The conveyor is active and moving forward.
Conveyor The conveyor is active and moving in reverse.
TSC The Through-Spindle Coolant (TSC) system is active.
TAB The Tool Air Blast (TAB) system is active.
Air Blast The Auto Air Gun is active.
Hi Light Indicates the optional High Intensity Lights (HIL) are turned ON and the doors are open. Duration is determined by Setting 238.
Refill The Coolant Refill feature is active. It mixes and adds coolant to the tank.
Coolant The main coolant system is active.

Be aware: Many service and repair procedures should be done only by authorized personnel. The service technicians at your Haas Factory Outlet (HFO) have the training, experience, and are certified to do these tasks safely and correctly. You should not do machine repair or service procedures unless you are qualified and knowledgeable about the processes.

Danger: Some service procedures can be dangerous or life-threatening. DO NOT attempt a procedure that you do not completely understand. Contact your Haas Factory Outlet (HFO) and schedule a service technician visit if you have any doubts about doing a procedure.

Feedback